|
Still deciding? Get samples of $ !
Request Sample
|
| Customization: | Available |
|---|---|
| Usage: | Signal Jammer |
| Type: | Wireless |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Item | Parameter | Remark | |||
| working frequency | 20M-6000M | ||||
| power | 100W | ||||
| Operating Voltage | 28V | 24-36V | |||
| Conversion efficiency | ≥42% | @100W | |||
| Adjustable output power | 10W~100W | Software set power | |||
| ALC power adjustment range | ≥20dB | Voltage Controlled Attenuation | |||
| gain | 48±1.0dB | ||||
| In-band fluctuation | ≤2.5dB | peak | |||
| spurious emissions | In working band | ≤-15dBm/1MHz | Measured when the center frequency plus CW signal to the maximum output power | ||
| Out- of-b and |
9KHz~1GHz | No higher than normal noise floor clutter |
|||
| 1G~12.75GHz | |||||
| Maximum allowable input power | ≥+10dBm | Lasts 1min without damage | |||
| Input VSWR | ≤1.35 | Add +28V, standard network output -10dBm |
|||
Output VSWR |
≤1.35 | No power, standard network | |||
| ≤1.35 | Power On, Dual Directional | ||||
High and low temperature test |
Working environment temperature (ºC) |
-10~+65ºC |
Low temperature can start, monitoring works normally | ||
| Gain Stability | ±1.5dB @-40ºC~ | ||||
| power stability | ±1dB @-40ºC~ | ||||
| Power Requirements | ≥8A @+28Vdc; | CW output 100W | |||
| Power supply interface, communication interface RS485 |
7W2 | Male, 1:485A; 2:485B | |||
| RF output connector | N-Female connector | ||||
| with 3 LED lights | POWER: Power indication; RUN: Running indication; ALARM: Alarm indication; |
||||
| physical dimension | 700M-6G:155*125*26mm; 20M-500M:155*125*35mm | ||||
| weight | <1Kg | ||||
Appearance (how to use) |
Signal source power amplifier integrated module (fixed on the radiator) | ||||
| Monitoring Function | Description | Remark | |
Amplifier part setting parameters |
Amplifier switch | Turn the amplifier on or off | |
| Alarm switch | Enable and disable the alarm function | ||
Downlink Power Control |
The maximum output power of the power amplifier can be set, the adjustment range is ≥20dB, and the high, medium and low power levels can be set |
||
Amplifier over temperature alarm |
The high temperature power amplifier shutdown threshold can be set, the power amplifier temperature exceeds 85 degrees, it will automatically shut down; 65 degrees will automatically restore |
||
| Amplifier overpower alarm | The actual power value is 2dB higher than the downlink ALC start control threshold and close |
||
| Power amplifier standing wave alarm | When the standing wave detection of the power amplifier is greater than 4, the power amplifier is automatically turned off |
||
| Amplifier overcurrent alarm | When the detection current of the power amplifier exceeds 12A, the power amplifier is automatically turned off |
||
| Amplifier under-power alarm |
When the power amplifier detection power is less than 33dBm, an under-power alarm is displayed |
||
| Amplifier overvoltage alarm | When the power amplifier voltage exceeds 32V, the power amplifier will automatically shut down |
||
| Amplifier undervoltage alarm |
Amplifier voltage <20V displays under-voltage alarm | ||
Amplifier part query parameters |
Amplifier switch status | If the power amplifier is set to "OFF", th state of power amplifier off state; other power amplifier state |
e |
| Downstream output power level value | Detect power amplifier output power value, detection range (Pomax+2, Pomax-20) | Detection accuracy: Pout±1dB |
|
| Downward standing wave ratio |
The standing wave is normally 1.2, when the load is mismatched, the query value is 4.0 |
||
){kind=link}